User Tools
operations:temphumidmonitor
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
operations:temphumidmonitor [2018/09/11 07:13] Jim Lovell [Hardware setup] |
operations:temphumidmonitor [2018/09/11 07:24] Jim Lovell |
||
|---|---|---|---|
| Line 36: | Line 36: | ||
| </code> | </code> | ||
| Connect them to the Raspberry Pi. Any GND or +5V pin will be fine. | Connect them to the Raspberry Pi. Any GND or +5V pin will be fine. | ||
| - | Use any digital pin on the Pi and make sure they are set to "False" in ''TempHumid.conf'' (you can give them an appropriate label though). | + | Use any digital pin on the Pi and make sure they are set to "False" in ''TempHumid.conf'' (you can give them an appropriate label though). See below. |
| ==== Accelerometer ==== | ==== Accelerometer ==== | ||
| Line 50: | Line 50: | ||
| </code> | </code> | ||
| + | Attach the accelerometer to the maser (or whatever you want to measure). You might want to align it according to the orientation diagram on the module. | ||
| ==== Analog (Eric) Temperature/Humidity Sensor ==== | ==== Analog (Eric) Temperature/Humidity Sensor ==== | ||
| This should also be connected to the Arduino: | This should also be connected to the Arduino: | ||
| Line 62: | Line 63: | ||
| - | ===== Software ===== | + | ===== DHT11 monitoring Software ===== |
| Software, config file etc are stored in ''~pi/TempHumid'' | Software, config file etc are stored in ''~pi/TempHumid'' | ||
| Line 87: | Line 88: | ||
| * ''start_THRecord.sh'' and ''start_THServer.sh'' are started automatically after the RPi boots into a desktop session, so a reboot of the RPi should start these processes. They are called from ''~/.config/lxsession/LXDE-pi/autostart''. Edit this file if you want to change what happens when the desktop starts. | * ''start_THRecord.sh'' and ''start_THServer.sh'' are started automatically after the RPi boots into a desktop session, so a reboot of the RPi should start these processes. They are called from ''~/.config/lxsession/LXDE-pi/autostart''. Edit this file if you want to change what happens when the desktop starts. | ||
| - | ==== Network config ==== | + | ===== Accelerometer, Analog temp/humid monitoring Software ====== |
| + | A work in progress... | ||
| + | |||
| + | ===== Software for IR remote control of aircon ====== | ||
| + | A work in progress... | ||
| + | |||
| + | ====== Network config ===== | ||
| + | This should be done already, but just in case... | ||
| For masertempke the IP address should be 131.217.61.28. | For masertempke the IP address should be 131.217.61.28. | ||
| For antennatempke the IP address should be 131.217.61.29. | For antennatempke the IP address should be 131.217.61.29. | ||
| Line 108: | Line 117: | ||
| [[operations:temphumidmonitorrpi|Configuring Raspberry Pis for Temperature and Humidity monitoring]] | [[operations:temphumidmonitorrpi|Configuring Raspberry Pis for Temperature and Humidity monitoring]] | ||
| - | |||
/home/www/auscope/opswiki/data/pages/operations/temphumidmonitor.txt · Last modified: 2019/03/25 21:20 by Jim Lovell
Page Tools
