User Tools
handover:crds95
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
handover:crds95 [2018/05/07 18:52] Simin Salarpour |
handover:crds95 [2018/05/08 16:55] (current) Simin Salarpour |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| * 16:30UT - Experiment started OK (Patrick) | * 16:30UT - Experiment started OK (Patrick) | ||
| + | * 17:00UT - Hobart late on source (WARNING: ONSOURCE status is SLEWING!) | ||
| + | * Also: 17:06,19:34,19:39,20:05,22:00,22:41,22:57,23:02,23:13 | ||
| + | * 13:00UT - Hobart has windstowed, wind speed reached 37 kph (Tiege) | ||
| **Katherine 12m** | **Katherine 12m** | ||
| Disk VSN: HOB+0029 | Data volume at beginning: 1.410 GB | Disk VSN: HOB+0029 | Data volume at beginning: 1.410 GB | ||
| + | (swapped out because of bad disk. approximately 1780.38 GB recorded) | ||
| + | |||
| + | Disk VSN: HOB+0033 | Data volume at beginning: 0 GB | ||
| * 16:30UT - Experiment started OK (Patrick) | * 16:30UT - Experiment started OK (Patrick) | ||
| Line 15: | Line 21: | ||
| * 17:30 - restarting mk5 did not fix previous error. it is due to a faulty disk in the module (shows up in get_stats procedure), which is causing writes to disk to be slower than usual. will email Mick and ask him to swap it with a good module in the morning, nothing I can do at the moment. | * 17:30 - restarting mk5 did not fix previous error. it is due to a faulty disk in the module (shows up in get_stats procedure), which is causing writes to disk to be slower than usual. will email Mick and ask him to swap it with a good module in the morning, nothing I can do at the moment. | ||
| * Set error to be ignored for the moment by changing M5 -104 in /usr2/control.ke/alarm_actions.txt (Patrick) | * Set error to be ignored for the moment by changing M5 -104 in /usr2/control.ke/alarm_actions.txt (Patrick) | ||
| - | * 18:40 - received the following alarms: ALARM: error st -998 reading systemclock1 and ALARM: error st -999 tcp/ip connection error. stowing and re-acquiring source fixed it. Affected scans are No0304-No0305. (Patrick) | + | * 18:40 - received the following alarms: |
| + | * ALARM: error st -998 reading systemclock1 and | ||
| + | * ALARM: error st -999 tcp/ip connection error. | ||
| + | * WARNING: error st -10 rampepochtime not -1 when preparing to load, check antenna is in "operate" | ||
| + | * WARNING: error st -5 error return from antenna, see mbus error | ||
| + | * stowing and re-acquiring source fixed it. Affected scans are No0304-No0305. (Patrick) | ||
| + | * 20:45 - Above error happened again, halted, stowed, and resumed schedule to fix it. Affected scans are No0324-No0326. (Patrick) | ||
| + | * 21:51 - Schedule halted to swap modules. New module is HOB+0033. (Patrick) | ||
| Line 25: | Line 38: | ||
| * 16:30UT - Yg module will not fit whole experiment (expected = 6.1TB, module = 6TB). Will need to be swapped over later. (Patrick) | * 16:30UT - Yg module will not fit whole experiment (expected = 6.1TB, module = 6TB). Will need to be swapped over later. (Patrick) | ||
| * 16:30UT - Experiment started OK (Patrick) | * 16:30UT - Experiment started OK (Patrick) | ||
| + | * 15:30UT - Module changed at scan 0458- No scans jeopardised I don't think. Guy | ||
| + | at YG will send them both to Washington. | ||
/home/www/auscope/opswiki/data/attic/handover/crds95.1525719161.txt.gz · Last modified: 2018/05/07 18:52 by Simin Salarpour
Page Tools
