User Tools
handover:r1897
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
handover:r1897 [2019/06/03 15:26] Lim Chin Chuan |
handover:r1897 [2019/06/03 23:43] (current) Jamie McCallum |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| Disk VSN: HAY-0062 | Data volume at beginning: 1.571 GB | Disk VSN: HAY-0062 | Data volume at beginning: 1.571 GB | ||
| - | Proc file does not seem to have been generated properly, this is causing issues noticeable in the test recording. I am using the r1895ke proc file now instead. Please note this if you need to re-setup the experiment at some point. | + | Proc file does not seem to have been generated properly, this is causing issues noticeable in the test recording. I am using the r1895ke proc file now instead. Please note this if you need to re-setup the experiment at some point. (Tiege) |
| + | |||
| + | ->Proc issue due to a typo in skedf.ctl (DNNC rather than DBBC). skedf.ctl may not be applied until after a restart of the FS. (JMc) | ||
| * 1700UT - Experiment started OK (Tiege) | * 1700UT - Experiment started OK (Tiege) | ||
| Line 13: | Line 15: | ||
| Disk VSN: HOB+0064 | Data volume at beginning: 1.699 GB | Disk VSN: HOB+0064 | Data volume at beginning: 1.699 GB | ||
| - | This setup happened after Jamie and Guifre were attempting top upgrade DBBC software. I closed the new DBBC software, opened the old, then restarted fs. Everything was fine (including test recording), however, while doing pointing check (after typing fivept) I encountered the error "TPI Overflow". This froze up the pointing check, not letting it progress any further. It was fixed by again restarting and resyncing the DBBC software. Not sure if just * 1700UT - Experiment started OK (Tiege)a one off quirk, but noting it down just in-case. This was all prior to schedule start so no data is affected. (Tiege) | + | This setup happened after Jamie and Guifre were attempting top upgrade DBBC software. I closed the new DBBC software, opened the old, then restarted fs. Everything was fine (including test recording), however, while doing pointing check (after typing fivept) I encountered the error "TPI Overflow". This froze up the pointing check, not letting it progress any further. It was fixed by again restarting and resyncing the DBBC software. Not sure if just a one off quirk, but noting it down just in-case. This was all prior to schedule start so no data is affected. (Tiege) |
| + | |||
| + | Also, drive information on system monitor for Yg seems to be completely broken. The message box is showing many Monica issues. Have tried restarting both Rxmon and Monica as a whole. This has not fixed it. Telescope appears to be working correctly, I may just need to restart a specific part of Monica that I do not know. (Tiege) | ||
| + | |||
| + | ->Drive info restored after restarting the antmon program [''/etc/init.dMonica.antmon stop && /etc/init.dMonica.antmon start'' as root] (JMc) | ||
| * 1700UT - Experiment started OK (Tiege) | * 1700UT - Experiment started OK (Tiege) | ||
/home/www/auscope/opswiki/data/attic/handover/r1897.1559575560.txt.gz · Last modified: 2019/06/03 15:26 by Lim Chin Chuan
Page Tools
