User Tools
software:yg_9.11.3_to_9.11.4
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
|
software:yg_9.11.3_to_9.11.4 [2013/10/02 01:56] Jim Lovell created |
software:yg_9.11.3_to_9.11.4 [2013/10/02 02:02] (current) Jim Lovell |
||
|---|---|---|---|
| Line 80: | Line 80: | ||
| 6. as root | 6. as root | ||
| - | cd /usr2/eremotectrl | + | cd /usr2/eremotectrl/make |
| make clean | make clean | ||
| make build | make build | ||
| Line 86: | Line 86: | ||
| 7. reboot | 7. reboot | ||
| - | |||
| - | 8. Log in as oper | ||
| - | cd /usr2/control | ||
| - | |||
| - | added the following to skedf.ctl: | ||
| - | |||
| - | * DBBC target values for IF counts in set-up procedure, up to 4 | ||
| - | * values for up to four IFs, in order, this will cause an error | ||
| - | * in IFx=... command execution if used for DBBC DDC versions | ||
| - | * before v101 | ||
| - | * default is nulls if not present | ||
| - | dbbc_if_targets 25000 25000 35000 35000 | ||
| - | *-------------------------------------------------------------- | ||
| - | * DBBC BBC TPI target levels | ||
| - | * has no effect for DDC versions before v103 | ||
| - | * default is null if not present | ||
| - | dbbc_bbc_target 16000 | ||
| - | |||
| - | cd /usr2/proc | ||
| - | modified station.prc as follows: | ||
| - | (F) This step is only for stations with DBBCs that are updating | ||
| - | from previous version of 9.11.x, x=0, 1, or 2. Three changes | ||
| - | are needed to the station.prc library: | ||
| - | |||
| - | (i) Please insert the command "bbc_gain=all,agc" at the end | ||
| - | of your SETUPA procedure. This command is a "no-op" | ||
| - | for DDC version less than v103, but including it is | ||
| - | recommended that be added for future backward | ||
| - | compatibility. For stations with v104 or higher, as | ||
| - | additional parameter specifying the target count level | ||
| - | can be added if it is desired, e.g., | ||
| - | "bbc_gain=all,agc,16000" | ||
| - | |||
| - | (ii) Add the procedure "BBC_LEVEL" to your station.prc | ||
| - | library. This can probably done most easily with the | ||
| - | following commands: | ||
| - | |||
| - | cd /usr2/proc | ||
| - | cp /usr2/fs/st.default/proc/bbc_level.prc . | ||
| - | pfmed | ||
| - | st,bbc_level::bbc_level,bbc_level | ||
| - | ex | ||
| - | rm bbc_level.prc | ||
| - | |||
| - | (iii) This step is only for stations with non-continuous cal and has | ||
| - | two parts. | ||
| - | |||
| - | (a) Edit the CALTSYS_MAN procedure and insert the command | ||
| - | "bbc_gain=all,man" right after the "IFMAN" command. | ||
| - | |||
| - | (b) Edit the CALTSYS procedure and insert the command | ||
| - | "bbc_gain=all,agc" right after the "IFAGC" command. | ||
| - | |||
| </code> | </code> | ||
/home/www/auscope/opswiki/data/attic/software/yg_9.11.3_to_9.11.4.1380679017.txt.gz · Last modified: 2013/10/02 01:56 by Jim Lovell
Page Tools
