User Tools
handover:a1508
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
handover:a1508 [2015/02/19 02:49] Ellen Manning |
handover:a1508 [2015/02/19 18:07] (current) liza |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| * 02:10 UT : swapped modules over. Looked like everything was running again fine but then the mark 5 went crazy and tried to record to both modules. We did a full power cycle 3 times to fix this. Scans between 050-0211 and 050-0239 are either bad or were missed. (Ellen) | * 02:10 UT : swapped modules over. Looked like everything was running again fine but then the mark 5 went crazy and tried to record to both modules. We did a full power cycle 3 times to fix this. Scans between 050-0211 and 050-0239 are either bad or were missed. (Ellen) | ||
| * Schedule resumed for scan 050-0241. (Ellen) | * Schedule resumed for scan 050-0241. (Ellen) | ||
| + | * 09:46UT: mark 5 lost connection. Halted schedule tried SSReset to no avail, hard rebooted as superuser, seemed to fix the problem. Schedule restarted 09:51, missed scans 050-0944b to 050-0956a (Imogen) | ||
| + | * 10:11UT: noticed that the time offset in the formatter (when issued mk5=dot? command) was more than 10ms. In fact, it was 50ms. However, this value fell with the next check and continued to fall until it was below 10ms. (Imogen) | ||
| + | * 10:54UT: mark 5 keeps losing connection, not sure why (Imogen) | ||
| + | * 11:49UT: scans 050-1146 to 050-1156 were lost due to attempt to heal the "ERROR m5 -104 mk5cn: time-out, connection closed" (restarted DIMino and fs, helped for now) (Liza) | ||
| + | * 12:02-04UT: DIMino stopped, restarted it twice, affected scans 050-1202, 050-1204a (Liza) | ||
| + | * 13:48-13:59UT: Problems with Mark5B, restarted DIMino repeatedly. Scans affected are 050-1348 to 050-1358. Meanwhile, clock jump occured, fmset synch performed 14:01;23 between scans 050-1400 and 050-1402 (Liza) Due to the Mark5 resetting, following scans were recorded to a wrong module UAO-0026/2000: | ||
| + | * 1 a1508_hb_050-1356+ | ||
| + | * 2 a1508_hb_050-1358 | ||
| + | * 3 a1508_hb_050-1400 | ||
| + | * 4 a1508_hb_050-1402 | ||
| + | * 16:45 restarted DIMino, fs, schedule. Scans 050-1645 and 050-1647 were affected (Liza) | ||
| + | * By the end, it recorded 300GB less due to repeated ERROR m5 -104 mk5cn: time-out, connection closed and attempts to recover it (Liza) | ||
| **Katherine 12m:** | **Katherine 12m:** | ||
| Line 41: | Line 53: | ||
| * The wind monitor has not been able to connect from 22:00 UT to 00:30 UT (and counting). (Ellen) | * The wind monitor has not been able to connect from 22:00 UT to 00:30 UT (and counting). (Ellen) | ||
| + | * By the end, it recorded 100GB less (Liza) | ||
| {{tag>}} | {{tag>}} | ||
/home/www/auscope/opswiki/data/attic/handover/a1508.1424314152.txt.gz · Last modified: 2015/02/19 02:49 by Ellen Manning
Page Tools
