User Tools

Site Tools


handover:aust41_42

This wiki is not maintained! Do not use this when setting up AuScope experiments!

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
handover:aust41_42 [2014/08/16 01:34]
Warren Hankey
handover:aust41_42 [2014/08/17 05:32]
Ross Turner
Line 1: Line 1:
 ====== AUST41+42 ====== ====== AUST41+42 ======
  
-ATTENTION AUST WEEKEND OBSERVER! 
 Ke: Ke:
- 
- has no modules in mk5ke to continue with those experiments. The module UAO-0018, that is in now, contains R4648ke and to be shipped to Washington. Perhaps there is a module in mk5-2ke and one can to switch to it, but I do not know, better call Martin. 
  
 Module USN+0224 8000 GB was loaded in Bank B but key not turned on! Martin attempting to get there, but probably expect late start.... Module USN+0224 8000 GB was loaded in Bank B but key not turned on! Martin attempting to get there, but probably expect late start....
  
  
- ​Recording finally started to USN+0225 at 00:39 after modules sorted. Looks like module in B USN+0224 has bad soft VSN (name too long) will need to sort out when there is a substantial gap in scans.+ ​Recording finally started to USN+0225 at 00:39 after modules sorted. ​Recorded data is -179 GB short of scheduled, due to late start. 
 + 
 + ​ATTENTION!  ​Looks like module in bank B USN+0224 has bad soft VSN (name too long warning) will need to sort out when there is a substantial gap in scans
 + 
 +Aust42 commenced on bank B module USN+0224, as above.
  
 Hb: Hb:
  
-Hb has only HOB+0041/6000 plus half of USN-0114/​4000 that already contains R4648hb, summing up to 8TB. Module change should be performed by one of the observers some time on Saturday.+Recording to HOB+0041 ​starting at zero GB.
  
-cheers, Liza+ ​Module changed in A to HOB+0023 6 TB ready for aust42 by Warren on Saturday. 
 + 
 +Hb automatically changed to bank A for start of scan 229-0530.
  
 Yg: Yg:
  
-Antenna stuck. Not in windstow. Dave local at yg went out to reset power in pedestal. Still no joy. Current ​Issue! Elevation brakes will not release. Need to switch power off in pedestal, open cabinet and switch to maintenance mode. Switch power back on, but to hand box control. ​See if you can drive it. Switch power back to remote mode. See if HMI interface ​can now drive telescope. Good luck with all of that....+Antenna stuck. Not in windstow, elevation brakes wont release. Dave local at yg went out to reset power in pedestal. Still no joy. 
 + 
 + Move to Current ​Issues! Elevation brakes will not release. fs, halt schedule. Need to switch power off in pedestal, open cabinet and switch to maintenance mode. Switch power back on, but this time to hand box control. ​Should be able to drive by hand. Switch power back over to remote mode. HMI interface ​should ​now drive telescope ​might need to "​Reboot Central"​ in HMI. fs, antenna=open,​ antenna=operate,​ resume schedule. Good luck with all of that...
 + 
 +Recorded data is -404 GB short of scheduled, due to late start.
  
  
/home/www/auscope/opswiki/data/pages/handover/aust41_42.txt · Last modified: 2014/08/17 05:32 by Ross Turner