User Tools

Site Tools


katherine_todo

This wiki is not maintained! Do not use this when setting up AuScope experiments!

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
katherine_todo [2011/02/06 02:41]
Brett Reid
katherine_todo [2014/07/26 06:21]
Jamie McCallum
Line 1: Line 1:
 ====== Katherine To Do ====== ====== Katherine To Do ======
 +
 +    * Phase cal testing (temperature stabilisation?​ Bad filters?)
 +    * DBBC service - check cables, internal connections,​ bad boards)
 +        * Apparently working as of 25/7/14 after replacing Fila OUT, reseating stack & PCI7200 card & cables.  ​
 +    * earthing of DBBC and MK5 units using proper earth connections
 +    * DBBC cont cal - tune for ~2-5% CONT CAL, 5-10% pulsed CAL
 +        * CONT CAL seems to be triggered when PULSED CAL is? Check wiring on spare board?
 +    * Y-factor tests - get all CAL factors via DBBC. 
 +    * <​del>​control room temp sensors - MoniCA
 +    * twister cable suspender
 +    * <​del>​fix UPS</​del>​
 +    * pedestal and maser room fan, fix/replace
 +    * <​del>​webcam clean</​del>​
 +    * <​del>​Upgrade mk5-2ke. Replace module back plane
 +    * <​del>​Back up all PCs
 +    * <​del>​Maser service.</​del>​
 +    * <​del>​tidy ptz wiring
 +    * <​del>​clean all sky cam lens</​del>​
 +    * check for rodents in genset
 +    * generator battery charger reduce electrolyte boiling
 +    * feed temp/press sensor
 +    * weed control
 +    * insect proofing of the hub
 +    * <​del>​pedestal base flange seal</​del>,​ recoat with paving paint
 +    * <​del>​grooves in concrete foundation to promote drainage</​del>​
 +    * remove rust from container and paint
 +
   * Feed tube   * Feed tube
-    * <​del>​Install hatch handle</​del>​ 
-    * <​del>​Install receiver and cal plates</​del>​ 
-    * <​del>​cabling from receiver box to feed tube</​del>​ 
     * <​del>​test</​del>​     * <​del>​test</​del>​
   * Hub   * Hub
-    * <​del>​Install dehumidifier and test '​gimbal'​ mechanism.</​del> ​Look at antenna step-response with CTScope+    * Look at antenna step-response with CTScope
     * Replace fan on RF box     * Replace fan on RF box
   * Pedestal   * Pedestal
     * <​del>​Evict wildlife</​del>​     * <​del>​Evict wildlife</​del>​
 +    * drain spare conduit
     * <​del>​Modify controller setting to accept remote resets, and test</​del>​     * <​del>​Modify controller setting to accept remote resets, and test</​del>​
   * Antenna structure   * Antenna structure
     * <​del>​Put close-outs around elevation jack once cabling, installation and testing is complete</​del>​     * <​del>​Put close-outs around elevation jack once cabling, installation and testing is complete</​del>​
   * Generator   * Generator
-    * <​del>​Fix fuel tank</​del>​ 
-    * <​del>​New (2nd hand) starter motor, wrong one.</​del>​ Get new one from India. <​del>​Fit Hobart one.</​del>​ 
-    * <​del>​test</​del>​ 
     * <​del>​Connect remote monitoring of diesel running and 'not in auto'</​del>​     * <​del>​Connect remote monitoring of diesel running and 'not in auto'</​del>​
-  * <​del>​Repalce Az gearbox oil</​del>​ 
   * Site   * Site
     * <​del>​Remove rubbish</​del>​     * <​del>​Remove rubbish</​del>​
 +    * weeding and mowing
 +    * shelter above container
   * hardware   * hardware
     * <​del>​Confirm full set of spares</​del>,​ record serial numbers     * <​del>​Confirm full set of spares</​del>,​ record serial numbers
   * Control room equipment   * Control room equipment
-    * <​del>​Do we need another IPS?</​del>​ No. 
-    * <​del>​Install DBBC</​del>​ 
-      * <​del>​Check cables and cards are securely connected, check for signs of damage</​del>​ 
-      * <​del>​Turn on and see if it works :​-)</​del>​ 
-      * <​del>​Run Gino's calibration procedure</​del>​ 
-    * <​del>​Install Ops PC</​del>​ 
-    * <​del>​Fire up Rubidium and Frequency Comparator, monitor stability</​del>​ Fail. 
-    * <​del>​Install second power meter, check comms with PCFS</​del>​ 
     * Set up suitable backup mechanism for timing PC (in case of disk failure)     * Set up suitable backup mechanism for timing PC (in case of disk failure)
   * RF/IF testing   * RF/IF testing
Line 46: Line 61:
       * <​del>​Determine gross pointing offsets and obtain a zeroth-order model (Jim)</​del>​       * <​del>​Determine gross pointing offsets and obtain a zeroth-order model (Jim)</​del>​
     * <​del>​Measure SEFD at all bands. Should be ~2500 Jy</​del>​     * <​del>​Measure SEFD at all bands. Should be ~2500 Jy</​del>​
-    * Fringe check to Hobart+    * <del>Fringe check to Hobart</​del>​
   * Software   * Software
     * Confirm PCFS can talk to:     * Confirm PCFS can talk to:
Line 91: Line 106:
       * Listening to the drives       * Listening to the drives
     * MASER list     * MASER list
-      * <​del>​Get prices from TechRentals for hire of equip</​del>​ 
-      * <​del>​check availability of He at MR engineering</​del>​ 
       * <​del>​check PLL battery fault cause</​del>​       * <​del>​check PLL battery fault cause</​del>​
       *        * 
     * breid List     * breid List
-      * <​del>​Exhaust extension for generator</​del>​ 
       * Dehydrator       * Dehydrator
-        * <​del>​Network comms</​del>​ 
-        * <​del>​Air-line upwards</​del>​ 
       * Dehumidifier       * Dehumidifier
-      * <​del>​Cable ties in the feed</​del>​ +      * Eye-bolt in the cone 
-      * <​del>​Door in the feed</​del>​ +      * Wash Subreflector
-      * <del>Eye-bolt in the cone</​del>​ +
-      * <del>Wash Subreflector</​del>​+
       * Doors in Hub, <​del>​trim</​del>​ and cutouts, <​del>​fit</​del>​       * Doors in Hub, <​del>​trim</​del>​ and cutouts, <​del>​fit</​del>​
       * Rod and hook for retrieving fall arrester       * Rod and hook for retrieving fall arrester
 +      * eye bolt for fall arrester
       * <​del>​Phase Cal xdB - Sband 1dB</​del>​       * <​del>​Phase Cal xdB - Sband 1dB</​del>​
       * UPS       * UPS
       * Maser battery PLL fault       * Maser battery PLL fault
 +      * run a sych and 100MHz rg58 coax
       * Camera       * Camera
         * <​del>​Lightning arrestor</​del>​         * <​del>​Lightning arrestor</​del>​
 +        * focus
         * <​del>​Lens:​ clean and check</​del>​         * <​del>​Lens:​ clean and check</​del>​
       * <​del>​Install window blind</​del>​s       * <​del>​Install window blind</​del>​s
Line 118: Line 129:
       * back shell on wind stow connector       * back shell on wind stow connector
       * <​del>​EL encoder offset parameters</​del>​       * <​del>​EL encoder offset parameters</​del>​
-      * <​del>​Send back cherry picker</​del>​ 
       * <​del>​Send back excess stuff such as nuts and bolts for Yarragadee</​del>​       * <​del>​Send back excess stuff such as nuts and bolts for Yarragadee</​del>​
       * <​del>​Raise fall arrest inertia reel</​del>​       * <​del>​Raise fall arrest inertia reel</​del>​
Line 127: Line 137:
       * <​del>​Label equipment</​del>​       * <​del>​Label equipment</​del>​
       * Label supension files containing equipment manuals       * Label supension files containing equipment manuals
-      * Sun shield for melted box at power inlet to donga+      * oil change in az gear boxes and check/fix cause of leak 
 +      * sort generator battery and charging system 
 +      * oil change generator 
 +      * painting pedestal rust spots 
 +      * painting container rust spots 
 +      * Thermal sensors calibrate 
 +      * Sort mark5 earthing and other problems 
 +      * Sort counter 3 
 +      * install additional switch 
 +      * wire in PDUs 
 +      * LAN cabling 
 +      * install IR light properly 
 +      * check lightning arresters
       *        * 
 +
 +Bunnings
 +  * pedestal Fans
 +  * Halogen globes 500W
 +  * Paraflood Low energy
 +  * rags
 +  * 9V batteries
 +  * Vac cleaner bags. for shop vac
 +  * 3 in one oil for fan motors
 +  * 
 +
 +
 +Car parts NT
 +  * diesel oil
 +  * diesel filter
 +  * fan bearing grease
 +
 +Take
 +  * Switch 24port 1Gbps
 +
 +
 +
/home/www/auscope/opswiki/data/pages/katherine_todo.txt · Last modified: 2014/07/26 06:21 by Jamie McCallum