User Tools

Site Tools


katherine_todo

This wiki is not maintained! Do not use this when setting up AuScope experiments!

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
katherine_todo [2012/08/22 13:54]
Brett Reid
katherine_todo [2014/07/26 06:20]
Jamie McCallum
Line 1: Line 1:
 ====== Katherine To Do ====== ====== Katherine To Do ======
  
- * Y-factor tests +    * Phase cal testing (temperature stabilisation?​ Bad filters?) 
- * control room temp sensors +    * <del> DBBC service - check cables, internal connections,​ bad boards) 
- * twister cable suspender +        * Apparently working as of 25/7/14 after replacing Fila OUT, reseating stack & PCI7200 card & cables. ​  
- * pedestal fan +    * earthing of DBBC and MK5 units using proper earth connections 
- * webcam ​install +    * DBBC cont cal - tune for ~2-5% CONT CAL, 5-10% pulsed CAL 
- * tidy ptz wiring +        * CONT CAL seems to be triggered when PULSED CAL is? Check wiring on spare board? 
- * clean all sky cam lens +    ​* Y-factor tests - get all CAL factors via DBBC.  
- * check for rodents in genset +    <del>control room temp sensors ​- MoniCA 
- * feed temp/press sensor +    * twister cable suspender 
- * phasecal reg +    * <​del>​fix UPS</​del>​ 
- * weed control +    ​* pedestal ​and maser room fan, fix/replace 
- * fix UPS +    <del>webcam ​clean</​del>​ 
- * insect proofing of the hub +    * <​del>​Upgrade mk5-2ke. Replace module back plane 
- * pedestal base flange seal +    * <​del>​Back up all PCs 
- * grooves in concrete foundation to promote drainage +    * <​del>​Maser service.</​del>​ 
- * remove rust from container and paint+    <del>tidy ptz wiring 
 +    <del>clean all sky cam lens</​del>​ 
 +    * check for rodents in genset 
 +    * generator battery charger reduce electrolyte boiling 
 +    ​* feed temp/press sensor 
 +    * weed control 
 +    * insect proofing of the hub 
 +    <del>pedestal base flange seal</​del>,​ recoat with paving paint 
 +    <del>grooves in concrete foundation to promote drainage</​del>​ 
 +    * remove rust from container and paint
  
   * Feed tube   * Feed tube
Line 25: Line 34:
   * Pedestal   * Pedestal
     * <​del>​Evict wildlife</​del>​     * <​del>​Evict wildlife</​del>​
 +    * drain spare conduit
     * <​del>​Modify controller setting to accept remote resets, and test</​del>​     * <​del>​Modify controller setting to accept remote resets, and test</​del>​
   * Antenna structure   * Antenna structure
Line 32: Line 42:
   * Site   * Site
     * <​del>​Remove rubbish</​del>​     * <​del>​Remove rubbish</​del>​
 +    * weeding and mowing
 +    * shelter above container
   * hardware   * hardware
     * <​del>​Confirm full set of spares</​del>,​ record serial numbers     * <​del>​Confirm full set of spares</​del>,​ record serial numbers
Line 49: Line 61:
       * <​del>​Determine gross pointing offsets and obtain a zeroth-order model (Jim)</​del>​       * <​del>​Determine gross pointing offsets and obtain a zeroth-order model (Jim)</​del>​
     * <​del>​Measure SEFD at all bands. Should be ~2500 Jy</​del>​     * <​del>​Measure SEFD at all bands. Should be ~2500 Jy</​del>​
-    * Fringe check to Hobart+    * <del>Fringe check to Hobart</​del>​
   * Software   * Software
     * Confirm PCFS can talk to:     * Confirm PCFS can talk to:
Line 99: Line 111:
       * Dehydrator       * Dehydrator
       * Dehumidifier       * Dehumidifier
-      * <del>Eye-bolt in the cone</​del>​ +      * Eye-bolt in the cone 
-      * <del>Wash Subreflector</​del>​+      * Wash Subreflector
       * Doors in Hub, <​del>​trim</​del>​ and cutouts, <​del>​fit</​del>​       * Doors in Hub, <​del>​trim</​del>​ and cutouts, <​del>​fit</​del>​
       * Rod and hook for retrieving fall arrester       * Rod and hook for retrieving fall arrester
 +      * eye bolt for fall arrester
       * <​del>​Phase Cal xdB - Sband 1dB</​del>​       * <​del>​Phase Cal xdB - Sband 1dB</​del>​
       * UPS       * UPS
       * Maser battery PLL fault       * Maser battery PLL fault
 +      * run a sych and 100MHz rg58 coax
       * Camera       * Camera
         * <​del>​Lightning arrestor</​del>​         * <​del>​Lightning arrestor</​del>​
 +        * focus
         * <​del>​Lens:​ clean and check</​del>​         * <​del>​Lens:​ clean and check</​del>​
       * <​del>​Install window blind</​del>​s       * <​del>​Install window blind</​del>​s
Line 122: Line 137:
       * <​del>​Label equipment</​del>​       * <​del>​Label equipment</​del>​
       * Label supension files containing equipment manuals       * Label supension files containing equipment manuals
 +      * oil change in az gear boxes and check/fix cause of leak
 +      * sort generator battery and charging system
 +      * oil change generator
 +      * painting pedestal rust spots
 +      * painting container rust spots
 +      * Thermal sensors calibrate
 +      * Sort mark5 earthing and other problems
 +      * Sort counter 3
 +      * install additional switch
 +      * wire in PDUs
 +      * LAN cabling
 +      * install IR light properly
 +      * check lightning arresters
       *        * 
 +
 +Bunnings
 +  * pedestal Fans
 +  * Halogen globes 500W
 +  * Paraflood Low energy
 +  * rags
 +  * 9V batteries
 +  * Vac cleaner bags. for shop vac
 +  * 3 in one oil for fan motors
 +  * 
 +
 +
 +Car parts NT
 +  * diesel oil
 +  * diesel filter
 +  * fan bearing grease
 +
 +Take
 +  * Switch 24port 1Gbps
 +
 +
 +
/home/www/auscope/opswiki/data/pages/katherine_todo.txt · Last modified: 2014/07/26 06:21 by Jamie McCallum