This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
katherine_todo [2012/08/22 13:38] Brett Reid |
katherine_todo [2014/07/26 06:21] (current) Jamie McCallum |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== Katherine To Do ====== | ====== Katherine To Do ====== | ||
+ | |||
+ | * Phase cal testing (temperature stabilisation? Bad filters?) | ||
+ | * DBBC service - check cables, internal connections, bad boards) | ||
+ | * Apparently working as of 25/7/14 after replacing Fila OUT, reseating stack & PCI7200 card & cables. | ||
+ | * earthing of DBBC and MK5 units using proper earth connections | ||
+ | * DBBC cont cal - tune for ~2-5% CONT CAL, 5-10% pulsed CAL | ||
+ | * CONT CAL seems to be triggered when PULSED CAL is? Check wiring on spare board? | ||
+ | * Y-factor tests - get all CAL factors via DBBC. | ||
+ | * <del>control room temp sensors - MoniCA | ||
+ | * twister cable suspender | ||
+ | * <del>fix UPS</del> | ||
+ | * pedestal and maser room fan, fix/replace | ||
+ | * <del>webcam clean</del> | ||
+ | * <del>Upgrade mk5-2ke. Replace module back plane | ||
+ | * <del>Back up all PCs | ||
+ | * <del>Maser service.</del> | ||
+ | * <del>tidy ptz wiring | ||
+ | * <del>clean all sky cam lens</del> | ||
+ | * check for rodents in genset | ||
+ | * generator battery charger reduce electrolyte boiling | ||
+ | * feed temp/press sensor | ||
+ | * weed control | ||
+ | * insect proofing of the hub | ||
+ | * <del>pedestal base flange seal</del>, recoat with paving paint | ||
+ | * <del>grooves in concrete foundation to promote drainage</del> | ||
+ | * remove rust from container and paint | ||
+ | |||
* Feed tube | * Feed tube | ||
* <del>test</del> | * <del>test</del> | ||
Line 7: | Line 34: | ||
* Pedestal | * Pedestal | ||
* <del>Evict wildlife</del> | * <del>Evict wildlife</del> | ||
+ | * drain spare conduit | ||
* <del>Modify controller setting to accept remote resets, and test</del> | * <del>Modify controller setting to accept remote resets, and test</del> | ||
* Antenna structure | * Antenna structure | ||
Line 14: | Line 42: | ||
* Site | * Site | ||
* <del>Remove rubbish</del> | * <del>Remove rubbish</del> | ||
+ | * weeding and mowing | ||
+ | * shelter above container | ||
* hardware | * hardware | ||
* <del>Confirm full set of spares</del>, record serial numbers | * <del>Confirm full set of spares</del>, record serial numbers | ||
Line 31: | Line 61: | ||
* <del>Determine gross pointing offsets and obtain a zeroth-order model (Jim)</del> | * <del>Determine gross pointing offsets and obtain a zeroth-order model (Jim)</del> | ||
* <del>Measure SEFD at all bands. Should be ~2500 Jy</del> | * <del>Measure SEFD at all bands. Should be ~2500 Jy</del> | ||
- | * Fringe check to Hobart | + | * <del>Fringe check to Hobart</del> |
* Software | * Software | ||
* Confirm PCFS can talk to: | * Confirm PCFS can talk to: | ||
Line 81: | Line 111: | ||
* Dehydrator | * Dehydrator | ||
* Dehumidifier | * Dehumidifier | ||
- | * <del>Eye-bolt in the cone</del> | + | * Eye-bolt in the cone |
- | * <del>Wash Subreflector</del> | + | * Wash Subreflector |
* Doors in Hub, <del>trim</del> and cutouts, <del>fit</del> | * Doors in Hub, <del>trim</del> and cutouts, <del>fit</del> | ||
* Rod and hook for retrieving fall arrester | * Rod and hook for retrieving fall arrester | ||
+ | * eye bolt for fall arrester | ||
* <del>Phase Cal xdB - Sband 1dB</del> | * <del>Phase Cal xdB - Sband 1dB</del> | ||
* UPS | * UPS | ||
* Maser battery PLL fault | * Maser battery PLL fault | ||
+ | * run a sych and 100MHz rg58 coax | ||
* Camera | * Camera | ||
* <del>Lightning arrestor</del> | * <del>Lightning arrestor</del> | ||
+ | * focus | ||
* <del>Lens: clean and check</del> | * <del>Lens: clean and check</del> | ||
* <del>Install window blind</del>s | * <del>Install window blind</del>s | ||
Line 104: | Line 137: | ||
* <del>Label equipment</del> | * <del>Label equipment</del> | ||
* Label supension files containing equipment manuals | * Label supension files containing equipment manuals | ||
+ | * oil change in az gear boxes and check/fix cause of leak | ||
+ | * sort generator battery and charging system | ||
+ | * oil change generator | ||
+ | * painting pedestal rust spots | ||
+ | * painting container rust spots | ||
+ | * Thermal sensors calibrate | ||
+ | * Sort mark5 earthing and other problems | ||
+ | * Sort counter 3 | ||
+ | * install additional switch | ||
+ | * wire in PDUs | ||
+ | * LAN cabling | ||
+ | * install IR light properly | ||
+ | * check lightning arresters | ||
* | * | ||
+ | |||
+ | Bunnings | ||
+ | * pedestal Fans | ||
+ | * Halogen globes 500W | ||
+ | * Paraflood Low energy | ||
+ | * rags | ||
+ | * 9V batteries | ||
+ | * Vac cleaner bags. for shop vac | ||
+ | * 3 in one oil for fan motors | ||
+ | * | ||
+ | |||
+ | |||
+ | Car parts NT | ||
+ | * diesel oil | ||
+ | * diesel filter | ||
+ | * fan bearing grease | ||
+ | |||
+ | Take | ||
+ | * Switch 24port 1Gbps | ||
+ | |||
+ | |||
+ |