User Tools
operations:agenda2020_09_24
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
operations:agenda2020_09_24 [2020/09/24 02:13] Earl Lester |
operations:agenda2020_09_24 [2020/10/08 00:56] Jayender Kumar |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | **Chair:** Earl | + | **Chair:** Jay |
| + | |||
| + | **Next meeting chair:** Eloise | ||
| - | **Next meeting chair:** | ||
| **Attended:** | **Attended:** | ||
| + | |||
| **Apologies:** | **Apologies:** | ||
| Line 10: | Line 12: | ||
| **General Issues** | **General Issues** | ||
| + | * CAL controller failure for HO 26 during AOV051 | ||
| + | * Autocorrelations have been funky for couple of H0 26 experiments ( AOV051 & R1966) | ||
| * | * | ||
| Line 15: | Line 19: | ||
| - | * | + | * Hb 12: |
| - | + | * AOV051: Experiment started with recording in only one stream. Check and make sure that it's record each scan in three stream(sxy,xx,xy) at the start of experiment. | |
| - | ====== AOV051 ====== | + | |
| - | + | ||
| - | **Hobart 12m** | + | |
| - | + | ||
| - | * Autocorrelations have been funky, suspect file has been messed with? Ignored for now (Eloise/Warren) | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | + | ||
| - | ====== AUM019 ====== | + | |
| - | + | ||
| - | Yarragadee 12m | + | |
| - | + | ||
| - | + | ||
| - | - 1820 to 1831 UT, received a consistent warning trak waiting at limit. No scan affected (mas) | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | Hobart 12m | + | |
| - | + | ||
| - | - 2240 UT No data being recorded. Restart jive5ab seems to have fixed issue (Warren) | + | |
| - | - 2250 UT Guifre also to check J2Start ??? (w) | + | |
| - | - 2256 UT First recordings (w) | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | ====== si0265 ====== | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | ** Hobart 12m ** | + | |
| - | + | ||
| - | * 1530UT - Experiment started ok (Prad) | + | |
| - | * DBus error pops up at intervals. IF source not defined for detector device? | + | |
| - | * proc file error - missing the edited preob/postob that would have recorded the X-band data. Only S-band recorded to module, no useful data recorded. (JMc) | + | |
| - | * NB - Use aumm5bhb.prc as the proc file! | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | ====== ohg127 ====== | + | |
| - | + | ||
| - | **Hobart 26m** | + | |
| - | * Issues with very large clkoff measurement, auto correlations, configuring dbbc. Have restarted / rebooted DBBC, mark5, hobart etc. Warren will look at it in the morning. | ||
| - | * 0537 - Experiment resumed after dealing with multiple issues. DBBC was in unusable state, apparently due to a fault in the 10 MHz reference cable. Also investigated RF/IF system following up on recentr non-detections. Found a failed cable compensator which has been bypassed. (JMc) | ||
| - | * Ongoing issue - No valid Tsys readings. Origin unclear. (JMc) | ||
/home/www/auscope/opswiki/data/pages/operations/agenda2020_09_24.txt · Last modified: 2020/10/08 02:22 by Jayender Kumar
Page Tools
