User Tools

Site Tools


operations:agenda2021_03_25

This wiki is not maintained! Do not use this when setting up AuScope experiments!

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Last revision Both sides next revision
operations:agenda2021_03_25 [2021/03/25 01:48]
Earl Lester created
operations:agenda2021_03_25 [2021/03/25 02:10]
Earl Lester
Line 3: Line 3:
 **Next meeting chair:** Pradyumna **Next meeting chair:** Pradyumna
  
-**Attended:​** ​+**Attended:​** ​Jamie, Simin, Lim, Mas, Pradyumna, Jay
  
 **Apologies:​**  ​ **Apologies:​**  ​
Line 10: Line 10:
 **General Issues** **General Issues**
  
 +    * auscope0 link vs new auscope site, (up and down with testing).
 +    * email exploder issues.
 +    * resume SI experiments from 16/4/21 - best time at end of r4 experiments,​ weekly, extra 1 hour, same mode.
 +    * Hobart 26 still out -- hopefully back by easter'​s end
     *      * 
- 
  
 **Handover Issues** **Handover Issues**
Line 20: Line 23:
   * started getting mk5 error 'error m5 -900 : not doing record'​. find out that data was not being recorded. restarted dbbc3ke, did setup again, but didn't help. Warren looked deep into it and found out proc file had setupvgos commented out. After correcting that, recording started smoothly. I've faced the same issue with previous mix mode experiment. I think '​setupvgos'​ is commented out in '​si.prc',​ where we copy it for a particular experiment. Not sure whether it is a permanent thing or someone did some editing recently. Have to check further on this. (Jay)   * started getting mk5 error 'error m5 -900 : not doing record'​. find out that data was not being recorded. restarted dbbc3ke, did setup again, but didn't help. Warren looked deep into it and found out proc file had setupvgos commented out. After correcting that, recording started smoothly. I've faced the same issue with previous mix mode experiment. I think '​setupvgos'​ is commented out in '​si.prc',​ where we copy it for a particular experiment. Not sure whether it is a permanent thing or someone did some editing recently. Have to check further on this. (Jay)
   * si.prc has been fixed, setupsx procedure alias for setupvgos had been commented out (Warren)   * si.prc has been fixed, setupsx procedure alias for setupvgos had been commented out (Warren)
 +  * Confirm safety of this fix, could cause clock breaks, should only run vgos at setup or on dbbc reconfig -- flexbuff time out -- 
   * First good scan is from 1732UT (Jay)   * First good scan is from 1732UT (Jay)
   * 0827UT ALARM: error st -998 reading systemclock1;​ ALARM: error st -999 illegal state error; Antenna communication software (antcn) problem; Try sending source=disable or antenna=open to reinitialise connection. "​antenna=open"​ and "​antenna=operate"​ brought back the connection after several times trying. Affected scans: 082-0828 to 082-0842a (Simin)   * 0827UT ALARM: error st -998 reading systemclock1;​ ALARM: error st -999 illegal state error; Antenna communication software (antcn) problem; Try sending source=disable or antenna=open to reinitialise connection. "​antenna=open"​ and "​antenna=operate"​ brought back the connection after several times trying. Affected scans: 082-0828 to 082-0842a (Simin)
Line 31: Line 35:
   * 2210UT - DBBC3 failed again (JMc). restarting server program on dbbc3hb (JMc)   * 2210UT - DBBC3 failed again (JMc). restarting server program on dbbc3hb (JMc)
   * 2322UT - Resumed after a full power cycle. Apparently ok... first good data expected from 2328 (JMc)   * 2322UT - Resumed after a full power cycle. Apparently ok... first good data expected from 2328 (JMc)
 +  * 
 +  * remote power cycle wiki notes
 +  * checkmk5 script not copied when sched etc. run on ops8... scp within bash not transferring...
 +  *  ​
  
    ​* ​ AUM030 - Hobart 12    ​* ​ AUM030 - Hobart 12
/home/www/auscope/opswiki/data/pages/operations/agenda2021_03_25.txt · Last modified: 2021/03/25 02:15 by Earl Lester