User Tools
katherine_todo
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
katherine_todo [2014/04/07 05:53] Jamie McCallum |
katherine_todo [2014/07/26 06:21] (current) Jamie McCallum |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| * Phase cal testing (temperature stabilisation? Bad filters?) | * Phase cal testing (temperature stabilisation? Bad filters?) | ||
| * DBBC service - check cables, internal connections, bad boards) | * DBBC service - check cables, internal connections, bad boards) | ||
| + | * Apparently working as of 25/7/14 after replacing Fila OUT, reseating stack & PCI7200 card & cables. | ||
| + | * earthing of DBBC and MK5 units using proper earth connections | ||
| * DBBC cont cal - tune for ~2-5% CONT CAL, 5-10% pulsed CAL | * DBBC cont cal - tune for ~2-5% CONT CAL, 5-10% pulsed CAL | ||
| - | * Y-factor tests - get all CAL factors via DBBC | + | * CONT CAL seems to be triggered when PULSED CAL is? Check wiring on spare board? |
| - | * control room temp sensors - MoniCA | + | * Y-factor tests - get all CAL factors via DBBC. |
| + | * <del>control room temp sensors - MoniCA | ||
| * twister cable suspender | * twister cable suspender | ||
| - | * fix UPS | + | * <del>fix UPS</del> |
| - | * pedestal fan | + | * pedestal and maser room fan, fix/replace |
| - | * webcam clean | + | * <del>webcam clean</del> |
| - | * tidy ptz wiring | + | * <del>Upgrade mk5-2ke. Replace module back plane |
| - | * clean all sky cam lens | + | * <del>Back up all PCs |
| + | * <del>Maser service.</del> | ||
| + | * <del>tidy ptz wiring | ||
| + | * <del>clean all sky cam lens</del> | ||
| * check for rodents in genset | * check for rodents in genset | ||
| + | * generator battery charger reduce electrolyte boiling | ||
| * feed temp/press sensor | * feed temp/press sensor | ||
| * weed control | * weed control | ||
| * insect proofing of the hub | * insect proofing of the hub | ||
| - | * pedestal base flange seal | + | * <del>pedestal base flange seal</del>, recoat with paving paint |
| - | * grooves in concrete foundation to promote drainage | + | * <del>grooves in concrete foundation to promote drainage</del> |
| * remove rust from container and paint | * remove rust from container and paint | ||
| Line 27: | Line 34: | ||
| * Pedestal | * Pedestal | ||
| * <del>Evict wildlife</del> | * <del>Evict wildlife</del> | ||
| + | * drain spare conduit | ||
| * <del>Modify controller setting to accept remote resets, and test</del> | * <del>Modify controller setting to accept remote resets, and test</del> | ||
| * Antenna structure | * Antenna structure | ||
| Line 34: | Line 42: | ||
| * Site | * Site | ||
| * <del>Remove rubbish</del> | * <del>Remove rubbish</del> | ||
| + | * weeding and mowing | ||
| + | * shelter above container | ||
| * hardware | * hardware | ||
| * <del>Confirm full set of spares</del>, record serial numbers | * <del>Confirm full set of spares</del>, record serial numbers | ||
| Line 51: | Line 61: | ||
| * <del>Determine gross pointing offsets and obtain a zeroth-order model (Jim)</del> | * <del>Determine gross pointing offsets and obtain a zeroth-order model (Jim)</del> | ||
| * <del>Measure SEFD at all bands. Should be ~2500 Jy</del> | * <del>Measure SEFD at all bands. Should be ~2500 Jy</del> | ||
| - | * Fringe check to Hobart | + | * <del>Fringe check to Hobart</del> |
| * Software | * Software | ||
| * Confirm PCFS can talk to: | * Confirm PCFS can talk to: | ||
| Line 101: | Line 111: | ||
| * Dehydrator | * Dehydrator | ||
| * Dehumidifier | * Dehumidifier | ||
| - | * <del>Eye-bolt in the cone</del> | + | * Eye-bolt in the cone |
| - | * <del>Wash Subreflector</del> | + | * Wash Subreflector |
| * Doors in Hub, <del>trim</del> and cutouts, <del>fit</del> | * Doors in Hub, <del>trim</del> and cutouts, <del>fit</del> | ||
| * Rod and hook for retrieving fall arrester | * Rod and hook for retrieving fall arrester | ||
| + | * eye bolt for fall arrester | ||
| * <del>Phase Cal xdB - Sband 1dB</del> | * <del>Phase Cal xdB - Sband 1dB</del> | ||
| * UPS | * UPS | ||
| * Maser battery PLL fault | * Maser battery PLL fault | ||
| + | * run a sych and 100MHz rg58 coax | ||
| * Camera | * Camera | ||
| * <del>Lightning arrestor</del> | * <del>Lightning arrestor</del> | ||
| + | * focus | ||
| * <del>Lens: clean and check</del> | * <del>Lens: clean and check</del> | ||
| * <del>Install window blind</del>s | * <del>Install window blind</del>s | ||
| Line 124: | Line 137: | ||
| * <del>Label equipment</del> | * <del>Label equipment</del> | ||
| * Label supension files containing equipment manuals | * Label supension files containing equipment manuals | ||
| + | * oil change in az gear boxes and check/fix cause of leak | ||
| + | * sort generator battery and charging system | ||
| + | * oil change generator | ||
| + | * painting pedestal rust spots | ||
| + | * painting container rust spots | ||
| + | * Thermal sensors calibrate | ||
| + | * Sort mark5 earthing and other problems | ||
| + | * Sort counter 3 | ||
| + | * install additional switch | ||
| + | * wire in PDUs | ||
| + | * LAN cabling | ||
| + | * install IR light properly | ||
| + | * check lightning arresters | ||
| * | * | ||
| + | |||
| + | Bunnings | ||
| + | * pedestal Fans | ||
| + | * Halogen globes 500W | ||
| + | * Paraflood Low energy | ||
| + | * rags | ||
| + | * 9V batteries | ||
| + | * Vac cleaner bags. for shop vac | ||
| + | * 3 in one oil for fan motors | ||
| + | * | ||
| + | |||
| + | |||
| + | Car parts NT | ||
| + | * diesel oil | ||
| + | * diesel filter | ||
| + | * fan bearing grease | ||
| + | |||
| + | Take | ||
| + | * Switch 24port 1Gbps | ||
| + | |||
| + | |||
| + | |||
/home/www/auscope/opswiki/data/attic/katherine_todo.1396850036.txt.gz · Last modified: 2014/04/07 05:53 by Jamie McCallum
Page Tools
