• Phase cal testing (temperature stabilisation? Bad filters?)
• DBBC service - check cables, internal connections, bad boards)
  • Apparently working as of 25/7/14 after replacing Fila OUT, reseating stack & PCI7200 card & cables.
• earthing of DBBC and MK5 units using proper earth connections
• DBBC cont cal - tune for ~2-5% CONT CAL, 5-10% pulsed CAL
  • CONT CAL seems to be triggered when PULSED CAL is? Check wiring on spare board?
• Y-factor tests - get all CAL factors via DBBC.
• control room temp sensors - MoniCA * twister cable suspender * <del>fix UPS
• pedestal and maser room fan, fix/replace
• webcam clean
• Upgrade mk5-2ke. Replace module back plane * <del>Back up all PCs * <del>Maser service.
• tidy ptz wiring * <del>clean all sky cam lens
• check for rodents in genset
• generator battery charger reduce electrolyte boiling
• feed temp/press sensor
• weed control
• insect proofing of the hub
• pedestal base flange seal, recoat with paving paint
• grooves in concrete foundation to promote drainage
• remove rust from container and paint

• Feed tube
  • test
• Hub
  • Look at antenna step-response with CTScope
  • Replace fan on RF box
• Pedestal
  • Evict wildlife
  • drain spare conduit
  • Modify controller setting to accept remote resets, and test
• Antenna structure
  • Put close-outs around elevation jack once cabling, installation and testing is complete
• Generator
  • Connect remote monitoring of diesel running and 'not in auto'
• Site
  • Remove rubbish
  • weeding and mowing
  • shelter above container
• hardware
  • Confirm full set of spares, record serial numbers
• Control room equipment
  • Set up suitable backup mechanism for timing PC (in case of disk failure)
• RF/IF testing
  • Install power meter plotting software on pcfs (Jim)
  • Check all four signals are getting through and bandpasses look reasonable
    • any signs of RFI?
    • Are cable compensators doing a reasonable job?
  • look for phase-cal tones at S and X. About the right level?
  • look for noise diode, check its strength
  • check that a tone can be put through the system
  • measure Y-factors at all four bands, calculate Tsys
  • Attempt to detect a bright source
    • Jim to provide list of precessed source coordinates
    • Determine gross pointing offsets and obtain a zeroth-order model (Jim)
  • Measure SEFD at all bands. Should be ~2500 Jy
  • Fringe check to Hobart
• Software
  • Confirm PCFS can talk to:
    • Antenna controller
      • Check source=stow command
    • GPIB devices (two counters and SML)
    • Weather station
    • Anemometer
    • Power meter
      • check Tsys measurement works
    • Mark5
  • Test Mark5
    • Both banks OK? Martin had a concern
  • MONICA
    • Logging information from:
      • RF equipment
      • IF box
      • Weather station
      • Anemometer
      • Antenna Controller
      • The counters
      • SML
      • Maser status
      • Site power status (mains or UPS/generator)
    • Documentation of how to access MONICA data
  • Check printing from PCFS works
  • Display screen setup and test.
    • Warning/alarm system when parameters exceed allowable range.
• Documentation for local users:
  • Disk handling logistics (dispatch and collection)
  • Disk conditioning
  • Disk labeling
  • How to use HMI
  • How to use the PCFS
  • How to control the antenna from the hand-box
  • How to get the antenna out of its limits
  • How to recover the FS PC in case of disk failure
  • How to recover the timing PC in case of disk failure
  • Routine antenna checks:
    • Check for blocked drainage (those wasps fill them with mud)
    • Check for water getting into feed tube, hub, pedestal, drives
    • Check for wildlife getting in to antenna structure
    • Check for overheating of RF equipment (via MONICA)
    • Listening to the drives
  • MASER list
    • check PLL battery fault cause
  • breid List
    • Dehydrator
    • Dehumidifier
    • Eye-bolt in the cone
    • Wash Subreflector
    • Doors in Hub, trim and cutouts, fit
    • Rod and hook for retrieving fall arrester
    • eye bolt for fall arrester
    • Phase Cal xdB - Sband 1dB
    • UPS
    • Maser battery PLL fault
    • run a sych and 100MHz rg58 coax
    • Camera
      • Lightning arrestor
      • focus
      • Lens: clean and check
    • Install window blinds
    • Audio - microphone
    • Wind auto-stow signal
    • back shell on wind stow connector
    • EL encoder offset parameters
    • Send back excess stuff such as nuts and bolts for Yarragadee
    • Raise fall arrest inertia reel
    • Cover over dehydrator in pedestal
    • Find water leak in conduit 2
    • Ladder storage in container
    • Assemble shelf unit for MK5 modules
    • Label equipment
    • Label supension files containing equipment manuals
    • oil change in az gear boxes and check/fix cause of leak
    • sort generator battery and charging system
    • oil change generator
    • painting pedestal rust spots
    • painting container rust spots
    • Thermal sensors calibrate
    • Sort mark5 earthing and other problems
    • Sort counter 3
    • install additional switch
    • wire in PDUs
    • LAN cabling
    • install IR light properly
    • check lightning arresters

Bunnings

• pedestal Fans
• Halogen globes 500W
• Paraflood Low energy
• rags
• 9V batteries
• Vac cleaner bags. for shop vac
• 3 in one oil for fan motors

Car parts NT

• diesel oil
• diesel filter
• fan bearing grease

Take

• Switch 24port 1Gbps