User Tools

Site Tools


operations:handover

This wiki is not maintained! Do not use this when setting up AuScope experiments!

Handover notes

Please use this page to write up any notes on anything that needs to be passed on to the next observer or should go into the end of experiment message.

Notes should be placed below the horizontal line as a new blog entry.

Continuing problems should be copied to the Current Issues page.

**Template for Handover notes:**

Be sure to add any specific notes about the experiment if required, for example “Special back end configuration for x reason”. Put as much detail as you can - the more the better.

It is ESSENTIAL to put your name after EVERY entry. Copy and paste the template into the new handover notes

====== Experiment Name ======

**Hobart 12m**

Disk VSN: abc-123 | Data volume at beginning: 2.34 GB

   * 1300UT a comment from me (user)

**Katherine 12m**

Disk VSN: | Data volume at beginning:  GB

   * 

**Yarragadee 12m**

Disk VSN: | Data volume at beginning:  GB

   * 1300UT Experiment started okay (JMc).

Format for entering a comment It is important to stick to this formula - there is a good reason we need this information, so please include it!

Time stamp in UT * Comment * (Your Name)

For Example:

20:00UT: Wind stows, Missed scans 012-3456 to 012-3457 (Jim)

20:50UT: Mark5 lost connection, had to restart Mark5 and reconfigure DBBC, called Jamie on call to fix, missed scans 012-3456 to 012-4567 (Jim)

Again - as much detail as you can. It is important to remember that these notes will be sent to the correlator, so please make sure they make sense to others.


R1965

Yarragadee 12m

Disk VSN: MPI-0419| Data volume at beginning: ??

  • 1700UT Experiment started okay (prad)
  • Clock sync off. Fixed at 1711UT. First 3 scans affected (Prad)
2020/09/21 14:52 · Pradyumna Kiran Kummamuru · 0 Comments
si0265

Hobart 12m

  • 1530UT - Experiment started ok (Prad)
  • DBus error pops up at intervals. IF source not defined for detector device?
  • proc file error - missing the edited preob/postob that would have recorded the X-band data. Only S-band recorded to module, no useful data recorded. (JMc)
  • NB - Use aumm5bhb.prc as the proc file!

Yarragadee 12m

Disk VSN: MPI-0419

  • 1530UT - Experiment started ok (Prad)
2020/09/21 14:50 · Pradyumna Kiran Kummamuru · 0 Comments
R4964

Yarragadee 12m

Disk VSN: NRAO-180| Data volume at beginning: ??

  • Experiment started okay ??
2020/09/18 18:34 · Jayender Kumar · 0 Comments
ohg127

Hobart 26m

Disk VSN: HOB+1012 | Data volume at beginning: ? GB

  • Issues with very large clkoff measurement, auto correlations, configuring dbbc. Have restarted / rebooted DBBC, mark5, hobart etc. Warren will look at it in the morning.
  • 0537 - Experiment resumed after dealing with multiple issues. DBBC was in unusable state, apparently due to a fault in the 10 MHz reference cable. Also investigated RF/IF system following up on recentr non-detections. Found a failed cable compensator which has been bypassed. (JMc)
  • Ongoing issue - No valid Tsys readings. Origin unclear. (JMc)

Yarragadee 12m

Disk VSN: HOB+0098 | Data volume at beginning: 10522 GB

  • 1800UT Experiment started okay (Patrick).
2020/09/16 13:47 · Patrick Yates
t2141

YARAGADEE 12 m

HOB 0098/1600

Experiment started OK

2020/09/15 21:35 · Earl Lester · 0 Comments
R4963

Yarragadee 12m

Disk VSN: USN-0069 | Data volume at beginning: 0.577 GB

  • 1830UT Experiment started okay (Jay).
2020/09/10 18:23 · Jayender Kumar · 0 Comments
/home/www/auscope/opswiki/data/pages/operations/handover.txt · Last modified: 2018/10/29 16:27 by Jesse Swan