User Tools
operations:agenda2020_04_09
This wiki is not maintained! Do not use this when setting up AuScope experiments!
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
operations:agenda2020_04_09 [2020/04/09 03:15] Patrick Yates |
operations:agenda2020_04_09 [2020/04/09 03:34] (current) Patrick Yates |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ** next week's chair: ** Katie | ** next week's chair: ** Katie | ||
| - | **Attended:** Mas, Earl, Tiege, Jamie, Katie, Prad | + | **Attended:** Mas, Earl, Tiege, Jamie, Katie, Prad, Eloise |
| **Apologies:** | **Apologies:** | ||
| Line 20: | Line 20: | ||
| * Observing procedure same as before. Still configuring & monitoring outside field system. | * Observing procedure same as before. Still configuring & monitoring outside field system. | ||
| * Future version of FS will be able to do everything itself. | * Future version of FS will be able to do everything itself. | ||
| + | * Fibre works on Mon/Tues | ||
| + | * Took out wiki, since been repaired. Shouldn't recur | ||
| + | * ops-serv2 was left off after power works 2 weeks ago. | ||
| + | * **Ho drives:** | ||
| + | * One of the drives can struggle to start. Motor encoder, affecting Y2 drive. | ||
| + | * Might need to start drives (using vdesk), then let it sit for a bit before moving it. | ||
| + | * Can see this looking at camera. Y2 drive current meter doesn't move. | ||
| + | * If it still doesn't work, this is a job for Brett or Warren | ||
| + | * Eric will probably need to replace motor encoder. | ||
| **Handover Issues** | **Handover Issues** | ||
| * AUA063 | * AUA063 | ||
| * **Yg:** Started on flexbuffyg, switched to mk5yg later | * **Yg:** Started on flexbuffyg, switched to mk5yg later | ||
| + | * fs machine was unbootable day before, couldn't fix it. | ||
| + | * ran using a script outside the field system, bit of a kludge | ||
| + | * had mk5 or module issue, possibly an issue with the mk5 iteslf. Alternative recording system is using dbbc + flexbuff. Might need to switch to this. | ||
| * R1941 | * R1941 | ||
| * **Yg:** pcfs froze, needed restarting | * **Yg:** pcfs froze, needed restarting | ||
| + | * pcfs machine is getting old. replacement machine is being configured onsite, will switch over at some point. | ||
| * APSG46 | * APSG46 | ||
| * **Ho:** | * **Ho:** | ||
| * wrong receiver on axis. | * wrong receiver on axis. | ||
| * Mk5 module write protect error | * Mk5 module write protect error | ||
| + | * Module was used in Tidbinbilla (modified mk5C). Causes issues if it's not erased before recording. Can't add to the module. | ||
| + | * Possibly not an issue with jive5ab, vs. dimino | ||
| * Focus platform linear bearings came loose, needed fixing | * Focus platform linear bearings came loose, needed fixing | ||
| + | * Have intercom to listen to cryogenics in focus cabin | ||
| + | * Heard clunking, paused observation to go up and fix it. | ||
| + | * Daily check from Mt Pleasant is good. | ||
| * Received continuous errors "Allocating memory for antenna monitoring". Fix was rebooting sys26m. | * Received continuous errors "Allocating memory for antenna monitoring". Fix was rebooting sys26m. | ||
| + | * Usually because drive pc has run out of monitoring points. Possibly due to network issues. | ||
| + | * Can often fix by terminating field system & restarting | ||
| + | * Check for any unnecessary / spare vdesk sessions & close them | ||
| + | * Guaranteed way to fix is rebooting sys26m, but this takes a while (~4 minutes) | ||
/home/www/auscope/opswiki/data/attic/operations/agenda2020_04_09.1586402137.txt.gz · Last modified: 2020/04/09 03:15 by Patrick Yates
Page Tools
