User Tools

Site Tools


operations:handover

This wiki is not maintained! Do not use this when setting up AuScope experiments!

Handover notes

Please use this page to write up any notes on anything that needs to be passed on to the next observer or should go into the end of experiment message.

Notes should be placed below the horizontal line as a new blog entry.

Continuing problems should be copied to the Current Issues page.

**Template for Handover notes:**

Be sure to add any specific notes about the experiment if required, for example “Special back end configuration for x reason”. Put as much detail as you can - the more the better.

It is ESSENTIAL to put your name after EVERY entry. Copy and paste the template into the new handover notes

====== Experiment Name ======

**Hobart 12m**

Disk VSN: abc-123 | Data volume at beginning: 2.34 GB

   * 1300UT a comment from me (user)

**Katherine 12m**

Disk VSN: | Data volume at beginning:  GB

   * 

**Yarragadee 12m**

Disk VSN: | Data volume at beginning:  GB

   * 1300UT Experiment started okay (JMc).

Format for entering a comment It is important to stick to this formula - there is a good reason we need this information, so please include it!

Time stamp in UT * Comment * (Your Name)

For Example:

20:00UT: Wind stows, Missed scans 012-3456 to 012-3457 (Jim)

20:50UT: Mark5 lost connection, had to restart Mark5 and reconfigure DBBC, called Jamie on call to fix, missed scans 012-3456 to 012-4567 (Jim)

Again - as much detail as you can. It is important to remember that these notes will be sent to the correlator, so please make sure they make sense to others.


r1991

Yarragadee 12m

Disk VSN: HOB+1006/16000 | Data volume at the beginning: 6906 GB

  • 1700UT Experiment started OK (Patrick)
2021/03/23 20:35 · Patrick Yates
AOV057

Katherine 12m

Disk VSN: flexbuffke

  • 1630UT experiment started Ok.
  • started getting mk5 error 'error m5 -900 : not doing record'. find out that data was not being recorded. restarted dbbc3ke, did setup again, but didn't help. Warren looked deep into it and found out proc file had setupvgos commented out. After correcting that, recording started smoothly. I've faced the same issue with previous mix mode experiment. I think 'setupvgos' is commented out in 'si.prc', where we copy it for a particular experiment. Not sure whether it is a permanent thing or someone did some editing recently. Have to check further on this. (Jay)
  • si.prc has been fixed, setupsx procedure alias for setupvgos had been commented out (Warren)
  • First good scan is from 1732UT (Jay)
  • 0827UT ALARM: error st -998 reading systemclock1; ALARM: error st -999 illegal state error; Antenna communication software (antcn) problem; Try sending source=disable or antenna=open to reinitialise connection. “antenna=open” and “antenna=operate” brought back the connection after several times trying. Affected scans: 082-0828 to 082-0842a (Simin)

Yarragadee 12m

Disk VSN: MPI+0817/8000/1024 | Data volume at the beginning: 0 GB

  • 1630UT Experiment started OK (Jay)
2021/03/22 03:00 · Jayender Kumar · 0 Comments
r4990

Yg 12m

Disk VSN: OAN-0006 | Data volume at beginning: 0 GB

  • 1830UT Experiment started OK (Katie)
2021/03/18 18:42 · Katie Vandorou · 0 Comments
AUM031

Hobart 12m

Disk VSN: flexbuffhb

  • 1800UT Experiment started ok (mas)
  • 1830UT, halted the schedule. Sampler 3 and 4 are bad. Reconfigured the DBBC3. Resume schedule at 1919UT. Missed scans from 076-1832 through 076-1943 (mas)
  • 2157UT halted the schedule again - DBBC3 delays bad again (JMc)
  • 2208UT - Resumed. aua073 data deleted from flexbuffhb to free ~20 TB (JMc)
  • 2210UT - DBBC3 failed again (JMc). restarting server program on dbbc3hb (JMc)
  • 2322UT - Resumed after a full power cycle. Apparently ok… first good data expected from 2328 (JMc)

Katherine 12m

Disk VSN: flexbuffke

  • 1800UT Experiment started OK (mas)

Yarragadee 12m

Disk VSN: HOB+0113/16000/1024 | Data volume at the beginning: 7.8 GB

  • 1800UT Experiment started OK (mas)
2021/03/17 19:28 · Noor Md Said
AUM030

Hobart 12m

Disk VSN: flexbuffhb

  • 1730UT Experiment started ok (Jay)
  • 1800UT Did not recorded data in 'sxy' stream till this point. fs wasn't talking to dbbcho. restarted dbbcho, did a quick re-setup. first scan with all 3 stream is from 1802UT(Jay & Warren)
  • 1908 UT /mnt/disk13 i/o errors (this was the one that flaked out last week) need to clone, replace. also means lost 3.2 TB free space. disk10 full (Warren)

Katherine 12m

Disk VSN: flexbuffke

  • 1730UT Experiment started ok (Jay)

Yarragadee 12m

Disk VSN: HOB+0113/16000/1024 | Data volume at beginning: 0 GB

  • 1730UT Experiment started Ok (Jay)
2021/03/16 17:07 · Jayender Kumar · 0 Comments
R1990

Yarragadee 12m

Disk VSN: HAY-0062/4000 | Data volume at beginning: : 0 GB

  • 1700UT experiment started okay(Jay)
2021/03/15 02:53 · Jayender Kumar · 0 Comments
/home/www/auscope/opswiki/data/pages/operations/handover.txt · Last modified: 2018/10/29 16:27 by Jesse Swan